Simu TSA Hz 2 Programming Manual Download Page 16

Page: 16 / 26

Hz Wireless Switches
and Receivers

Switch Style & Programming Button Location Reference Description

6301066

6301070

6301071

6301090

White

6301091

Ivory

6301080

White

6301081

Ivory

6301075

6301072

Slim Single Channel Hand Held

-Available in white

Recessed Designer Single Channel

Available in white and ivory

Hz Radio Receiver Motor Controller

This radio receiver can be used with the SIMU

standard AC motor series 120v-60hz. This control
is compatible with all the transmitter switches
shown above.

Hz Dry Contact Interface Transmitter

This radio transmitter can be used with the SIMU

Hz operator series 120v-60hz. This interface control
is compatible most A/V system hook-ups.

Recessed Designer Multi Channel

5 independent channels that can be programmed

to operate one or more motors.

-Available in white and ivory

Slim Multi Channel Hand Held

5 independent channels that can be programmed

to operate one or more motors.

-Available in white

Single Channel Surface Wall Mount

-Available in white

Program Button

FCC
Label

F C
Label

BACK OF TRANSMITTER

Program Button

SIDE OF TRANSMITTER

Program Button

TRANSMITTER CORE
(INSIDE CASE)

Programming Button & LED

DOWN

MTR COM

NEUT

HOT

z RECE

120 VAC

6 Hz

: 3010

REF

H y

t f

z D

on a tI

n e ace

RF :63

01072

Programming Button & LED

DOWN

STOP

COM

Battery

White
Black

Red

Green

Summary of Contents for TSA Hz 2



























Search results

Summary of Contents for TSA Hz 2

Reviews:

Related manuals for TSA Hz 2

Brands by name

Popular brands

Simu TSA Hz 2, Programming Manual

Search results

Summary of Contents for TSA Hz 2

Reviews:

Related manuals for TSA Hz 2

Brands by name

Popular brands