background image

SYNCHRONIZING CONTROL

Installation and Operation Instructions

POWER

BLACK

WHITE

GREEN

MOTOR1

MOTOR2

WHITE

WHITE

GREEN

GREEN

RED

RED

BLACK

BLACK

SYNCHRO

BLACK

WHITE

RED

GREEN

BROWN

DESCRIPTION

OPERATING INSTRUCTIONS

WIRING DIAGRAM

SOMFY'S Synchronized Control is designed to control two motors simultaneously.  When two Somfy 
motors are mounted in a single tube, moving a single window treatment, it is important that the 
motors coincide with each other. The Synchronized control actuates and stops both motors at the 
same time.  This helps prevent damage to the tube, motor and window treatment.  The Synch Control 
comes with either momentary or maintained outputs to suit various installation requirements.  

Fuse rated at 15A, 250vAC

A.  System Power Up

 

NOTE:  Damage to the motor may occur over time if limits are 

not set on both motors.

1.

  

With power off, wire the Synchronizing Control as indicated below.  Turn all 

  

      circuit breakers on (Note: motors should not move).

B.  Momentary Output Operation

2.

  

Reset the limits of each motor by pressing in both limit switches of each 

      motor (4 total).  

NOTE:

  until the  limits are set, caution must be exercised 

Connect a single-pole, double-throw switch to the terminal bloc as indicated 

      when moving  the window treatment.

below.  When the UP direction is activated, the window covering will raise.  The 

3.

  

Activate the UP direction using the low voltage switch.  If the motorized 

treatment will move for the duration the switch is activated.  When the switch is 

      window treatment does not raise or retract, reverse the black and red wires 

moved to the CENTER position, the motors will stop.

      on both motors.

4.

  

When the treatment has reached the desired upper limit, depress the limit 

C.  Maintained Output Operation

 

      switch (switch is now out) on one motor, then the other.  The upper limits 
      are now set.

Connect an IGC switch to the modular jack as indicated below.  If the DOWN 

5.

  Activate the DOWN direction using the low voltage switch.  When the 

button is pressed, the window treatment will lower or extend.  Press the STOP 

     treatment has reached the desired lower limit, depress the limit switch on the 

button at any time to stop the motors.

     first motor, then the other.  The lower limits are now set.

BROWN

BLACK

RED

WHITE

GREEN

COLOR CODE

UP

DOWN

GND

MOTOR1

GROUND

NEUTRAL

HOT

MOTOR2

R

R

NO CONNECTIONS

Low Voltage

Switch Connections

Part No:  1822159  Momentary Output
Part No:  1822161  Maintained Output

REF. NO:

  

2500410 B

SOMFY SYSTEMS, INC.

47 Commerce Drive 
Cranbury, NJ 08512

SOMFY CANADA

6315 Shawson Drive, Unit #1
Mississauga, Ontario L5T1J2

SOMFY SYSTEMS, INC. reserves the right to change, 
update or improve this document without prior notice.

SOMFY SYSTEMS, INC.    8/07

C

Summary of Contents for TSA Hz 2



























Reviews: