Simu TSA Hz 2 Programming Manual Download Page 14

Page: 14 / 26

Hz Wireless Receiver
Instruction

1)Pressing the up or down button on the transmitter will start
the motor in the selected direction.
2)The motor can be stopped at any point by pressing the
center (stop) button on the transmitter.
3)If the motor is stopped at the top limit, pressing the center
button on the transmitter will move the motor to the one of
the programmed intermediate stops. Pressing the center
(stop) button when the motor is stopped at the bottom limit
will cause the motor to move to the other intermediate stop.

1)A HARD WIRED WALL SWITCH (single pole, single throw,
Momentary) can be connected as per the wiring diagram
above. Each press of the switch will move the motor to the
Next step in the sequence. Up, Stop, Down, Stop, Up,...

light. Press the programming button on the new transmitter. That
transmitter has now been memorized by the receiver
2)To delete a transmitter from the memory of the receiver, press the
programming button on the

Hz receiver

until the LED lights. Press the

programming button on the transmitter you want to delete.
3)To delete all transmitters from the memory of the

Hz receiver

, press and

hold the programming button on the receiver until the LED blinks.

To program the

Top Down Intermediate Position

, bring the motor to the

top limit. Press and hold the down and center buttons until the motor starts
to move, then release the buttons. Stop the motor at the desired position.
Press the center button for 2 seconds.
2)To program the

Bottom Up Intermediate Position

, bring the motor

the

bottom limit. Press and hold the up and center buttons until the motor starts
to move, then release the buttons. Stop the motor at the desired position.
Press the center button for 2 seconds.

1)To add a new transmitter, press the programming button of

3)To delete an intermediate position, use the center button to move the motor

The already memorized transmitter for more than 2

to that position. After the motor stops at that position, press and hold the

seconds. The programming LED on the

Hz receiver

will

center button until the LED on the Hz receiver stops blinking (about 10 sec.)

DESCRIPTION

INSTALLATION

1) Mount the

Hz Receiver

as close to the motor as possible. Avoid

mounting the receiver on metallic surfaces as this will reduce the range. If
mounted outside, make sure to use the watertight strain reliefs and mount
the box so the strain relief fittings face downward to avoid rain seepage.
2) If using a hardwired low voltage switch, locate it no more that 100 feet
from the receiver.

The UL Listed

Hz Receiver

allows control of any standard (non-Hz) T5 or

T6 motor from any of the Hz handheld or wall switch, wireless transmitters.
Packaged in an outdoor weatherproof box the

Hz Receiver

includes

terminals for an optional hard wired low voltage switch. In addition to
allowing standard motors to be incorporated into a Hz motor system, the
receiver can be programmed with two intermediate stop positions.

Reference No: 6301075

WIRING & INITIAL PROGRAMMING

MOTOR

HOT

NEUTRAL

GROUND

Programming Button & LED

To Optional
Low Voltage Switch

NOTE:

Mount control with
strain reliefs
facing downward!

DOWN

MTR COM

NEUT

HOT

BLACK

RED

GREEN

WHITE

COLOR CODE

NOTICE: For installation by a qualified electrician in accordance with
national and local electrical codes and the following instructions.
1)CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power
before installing. Never wire energized electrical components
Turn the power on after the wiring is complete.
2)If using a multi channel transmitter,

make sure the transmitter is on

the channel you wish

the

Hz Receiver

to respond to.

3)Press and hold the programming button on the

Hz Receiver

until

the LED lights (about 5 seconds) and release it. The LED should
stay on.
4)Quickly press the programming button on the transmitter and hold
it until the LED on the

Hz Receiver

blinks and goes out.

5)The

Hz Receiver

should now respond to the transmitter. If the

motor runs in the wrong direction when activated from the
transmitter, turn off power to the

Hz Receiver

and reverse the red

and black motor leads.

OPERATING INSTRUCTIONS

LOW VOLTAGE SWITCH

PROGRAMMED INTERMEDIATE POSITIONS