background image

BA_M-SHEV_EN_17

www.simon-protec.com

Date: 30.07.2019

Issue: 1.7/07.2019

[email protected]

Page 5

Preface

1.3 Functional description

The control modules of the electrical control system M-SHEV 
use bus technology to communicate with each other. In case 
of an ALARM-trigger or during daily ventilation operations, the 
M-SHEV controls the connected opening actuators.The 
ventilation functions also serve as regular functional checks 
of the smoke and heat ventilation system.

Smoke and heat extraction systems belong to the field of 
preventive fire protection. By installing them, lives can be 
saved in an emergency. The building permit authority decides 
whether and how the smoke control system must be installed 
in the building. Before proceeding with the installation, please 
check once again if the size of the smoke and heat extraction 
system is compliant with the official regulations in order to 
ensure sufficient system functionality. 

The control systems of the M-SHEV product family consist of 
four components (optionally up to six):

• Power supply 

(switching power supply, charging device and battery)

• Central interface ZI-100

• Sensor interface SI-100

• Motor relay MR-120

• Message interface MI-100 

(optional / not included in the standard scope of delivery)

• Bus interface BI-100 

(optional / not included in the standard scope of delivery)

All components are equipped with tension spring terminals 
(0.5 mm² – 2.5 mm²).

Table 1: Mechanical properties M-SHEV-10-AP

Dimensions (W x H x D)

Weight (including battery)

14.3 kg 

Protection rating

IP20 according to EN 60 529

Housing

Steel sheet (powder-coated)

Colour

RAL 9010

Table 2: Mechanical properties M-SHEV

Dimensions (W x H x D)

1

1.

Standard sizes; dimensions may vary according to customer 

requirements.

Protection rating

2

2.

If suitable cable glands are used.

IP66 according to EN 60 529

Housing

Steel sheet (powder-coated)

Colour

RAL 7035

Table 3: Connection and operation

Connection

See Chapter 4 “Electrical 
connection” on page 20
.

Actuator cut-off in every position 
(STOP command)

Yes

1

1.

Only in ventilation mode, without dead man's function.

Deadlock function according 

prEN 12101-9 (re-triggering)

Deadlock enabled

(can be activated/deactivated 
via SIMON LINK on the 

MR-120)

Maximum cable length between 
control unit and actuator

See Chapter 4.4 “Motor relay 
– MR-120” on page 22.

Maintenance

See supplementary sheet 
“Safety instructions and 
warranty conditions”!

Table 4: Installation and ambient conditions

Operational temperature

-5 to 40 °C 

1

1.

This temperature range applies to all components of the M-SHEV 

System (incl. battery).

Storage temperature

Suitable for external installation

Only with special types of 
housings – in case of doubt, 
please contact our technical 
sales department.

Table 5: Approvals and certificates

EU compliant

In accordance with 

EMC Directive 2014/30/EU and 

Low Voltage Directive 2014/35/EU.

Power supply

EN 12101-10 (Smoke and heat control sys-
tems – Part 10: Power supplies)

• M-SHEV-10-AP:

406 x 444 x 170 mm

• M-SHEV-10: 

400 x 600 x 200 mm 

• M-SHEV-24: 

500 x 500 x 200 mm 

• M-SHEV-48: 

600 x 600 x 250 mm 

• M-SHEV-72: 

800 x 800 x 250 mm 

Summary of Contents for M-SHEV Series

























Reviews: