background image

BA_M-SHEV_EN_17

www.simon-protec.com

Date: 30.07.2019

Issue: 1.7/07.2019

[email protected]

Page 7

Components — Power supply

Figure 4: M-SHEV-48 power supply

Figure 5: M-SHEV-72 power supply

2.1.1 Emergency power supply

The emergency power supply of the M-SHEV product family 
is ensured by two 12 V backup batteries. Only VdS approved 
lead batteries are permitted.

Switching between mains and emergency operation is auto-
matic if necessary. 

2.1.2 Regulating the I / U charge

Lead batteries are charged in accordance with the re-
quirements of EN 12101-10. The control system recognises if 
a lead battery is missing or faulty (self-diagnosis) and gener-
ates an error signal on the SHEV-emergency button (yellow 
LED) and the central interface (yellow LED).

2.1.3 Monitoring the monitor input for sequential 

control (mains/emergency operation)

The charging device switches to emergency power supply 
(monitoring function) in case of a mains failure, undervoltage 
of the power supply or if the primary power supply fails. 

2.1.4 Technical data (rated values)

Table 6: 

Operating voltage 

(continuous operation)

230 V AC

Permissible voltage range 

(short-time operation)

195 V AC to 264 V AC

Power consumption

1

1.

Power consumption at maximum output load.

1.45 A (M-SHEV-10)

4.4 A (M-SHEV-24)

8.8 A (M-SHEV-48)

13.2 A (M-SHEV-72)

Pre-fuse for mains isolation (-F1)

D01 16 A (gL/gG)

Connection power

385 VA (M-SHEV-10)

1012 VA (M-SHEV-24)

2024 VA (M-SHEV-48)

3069 VA (M-SHEV-72)

Inrush current

 30 A

 45 A (M-SHEV-10)

Frequency range

47 Hz to 63 Hz

Power supply conductor 

cross-section

at least 1.5 mm²

Terminal design

0.5 mm² – 2.5 mm²

Protection class

I

Mains connection data 

Table 7: Technical data for the switching power 

supply 10 A (-G1)

Input voltage

195 – 264 V AC

Output voltage

24 V DC (±1%)

Output voltage ripple

 80 mV (Vpp)

Output power

0 – 10 A / 240 W

 

Lead batteries 

Switching power 

Charging device 

Pre-fuse (-F1)

Switching power 

supply (-G2)

(2 x 17 Ah)

(-LB140/A1)

supply (-G1)

Lead batteries 

Switching power 

Charging device 

Pre-fuse (-F1)

Switching power 

Switching power 

supply (-G2)

supply (-G3)

(-LB160/A1)

supply (-G1)

(2 x 24 Ah)

Summary of Contents for M-SHEV Series

























Reviews: