Specification
Voltage: ..............................230V~ 50Hz
Frequency: .........................50Hz
Power: ...............................1400W
Working Pressure: .............6Mpa
Max Pressure: ...................14Mpa
Working Flow Rate: ...........5.5L/min
Sound Pressure: ................81dB(A)
Sound Power: ....................94dB(A)
Uncertainty ........................3.0dB(A)
Protection Class: ...............
Degree Of Protection .........IPX5
The sound intensity level for the operator
may exceed 85dB(A) and sound protection
measures are necessary.
As part of our ongoing product development,
specifications of Silverline products may alter
without notice.
4
GB
if any of the supplied guards are missing. If any guards are
damaged, replace before use.
Remove adjusting keys
•
Always check to see that keys and adjusting devices are
removed from the tool before use.
Clean the work area
•
Accidents can occur where benches and work areas are
cluttered or dirty. Floors must be kept clear. Avoid working
where the floor is slippery. If working outdoors, make
yourself aware of all potential slip and trip hazards before
using this tool.
Children and pets
•
Children and pets should always be kept at a safe distance
from your work area. Lock tools away where children can’t
get access to them. Do not allow children or untrained
persons to use this tool.
Use the correct tool
•
Don’t force or attempt to use a tool for a purpose it was not
designed.
•
This tool is not intended for industrial use.
Wear suitable clothing and footwear
• Don’t wear loose fitting clothing, neckties, jewellery, or other
items which may become caught. Wear non slip footwear,
or footwear with protective toe caps where appropriate.
Long hair should be covered or tied back.
Keep your balance
•
Don’t over reach, keep proper footing at all times, do not
use tools when standing on an unstable surface.
Accessories
•
The use of any attachment or accessory other than those
mentioned in this manual could result in damage or injury.
The use of improper accessories could be dangerous, and
may invalidate your warranty.
Secure work
•
Where possible, always secure work. If appropriate use a
clamp or vice, it will allow you to use both hands to operate
your tool.
Check for damaged or missing parts
•
Before each use, check if any part of the tool is damaged
or missing, check carefully that it will operate properly
and perform its intended function. Check alignment of
moving parts for binding. Any guard or other part that is
damaged should be immediately repaired or replaced by an
authorised service centre.
DO NOT USE IF DEFECTIVE.
Electrical Safety
• To prevent fire or shock hazard, do not expose this product
to rain, water or moisture.
•
There are no user serviceable parts inside except those
referred to in this manual.
• Always refer servicing to qualified service personnel. Never
remove any part of the casing unless qualified to do so; this
unit contains dangerous voltages.
•
Use of a residual current device will reduce the risk of
electric shock.
Dangerous environment
•
Do not use power tools in damp or wet conditions, or
expose them to rain. Provide adequate surrounding work
space and keep area well lit. Do not use power tools
where there is a risk of explosion or fire from combustible
material, flammable liquids, flammable gases, or dust of an
explosive nature. When using power tools avoid contact
with any earthed items such as pipes, radiators, cookers,
refrigerators, metal baths and taps.
General Safety
Carefully read and understand this manual and any label
attached to the tool before use. Keep these instructions with
the product for future reference. Ensure all persons who use
this product are fully acquainted with this manual.
Even when used as prescribed it is not possible to eliminate
all residual risk factors. Use with caution. If you are at all
unsure of the correct and safe manner in which to use this
tool, do not attempt to use it.
Keep guards in position
•
Always keep guards in position, in good working order,
correctly adjusted and aligned. Never attempt to use a tool
Description of Symbols
The rating plate on your tool may show symbols. These
represent important information about the product or
instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction Manual.
Double insulated for additional protection.
Conforms to relevant legislation and safety
standards.
Environmental Protection
Waste electrical products should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authority or
retailer for recycling advice.
190218_Manual.indd 4
14/10/2010 09:23
