manualshive.com logo in svg

Silicon Laboratories Si5396 Series, Reference Manual

Share
Download
Silicon Laboratories Si5396 Series Reference Manual Download Page 151

the BWx_PLLC, FAST_BWx_PLLC, and BWx_HO_PLLC parameters to take effect. Note that individual SOFT_RST_PLLC (0x001C[3])

does not update the bandwidth parameters.

Table 15.212.  0x0615-0x061B MC Divider Numerator for DSPLL C

Reg Address

Bit Field

Type

Setting Name

Description

0x0615

7:0

R/W

M_NUM_PLLC

56-bit number

0x0616

15:8

R/W

M_NUM_PLLC

0x0617

23:16

R/W

M_NUM_PLLC

0x0618

31:24

R/W

M_NUM_PLLC

0x0619

39:32

R/W

M_NUM_PLLC

0x061A

47:40

R/W

M_NUM_PLLC

0x061B

55:48

R/W

M_NUM_PLLC

The MC divider numerator values are calculated by ClockBuilder Pro for a particular frequency plan and are written into these registers.

Table 15.213.  0x061C-0x061F MC Divider Denominator for DSPLL C

Reg Address

Bit Field

Type

Setting Name

Description

0x061C

7:0

R/W

M_DEN_PLLC

32-bit number

0x061D

15:8

R/W

M_DEN_PLLC

0x061E

23:16

R/W

M_DEN_PLLC

0x061F

31:24

R/W

M_DEN_PLLC

The loop MC divider denominator values are calculated by ClockBuilder Pro for a particular frequency plan and are written into these

registers.

Table 15.214.  0x0620 M Divider Update Bit for PLL C

Reg Address

Bit Field

Type

Setting Name

Description

0x0620

0

S

M_UPDATE_PLLC Must write a 1 to this bit to cause PLL C M divider

changes to take effect.

Bits 7:1 of this register have no function and can be written to any value.

Table 15.215.  0x0621 DSPLL C M Divider Fractional Enable

Reg Address

Bit Field

Type

Setting Name

Description

0x0621

3:0

R/W

M_FRAC_MODE_P

LLC

M feedback divider fractional mode.

Must be set to 0xB for proper operation.

0x0621

4

R/W

M_FRAC_EN_PLL

C

M feedback divider fractional enable.

0: Integer-only division

1: Fractional (or integer) division - Required for DCO

operation.

0x0621

5

R/W

Reserved

Must be set to 1 for DSPLL C

Si5397/96 Reference Manual

Si5397A/B Register Map

silabs.com

 | Building a more connected world.

Rev. 0.9  |  151

Summary of Contents for Si5396 Series






























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands