manualshive.com logo in svg

Sierra InnovaMass 240i Series, Instruction Manual, Page: 63 / 115

Share
Download
Sierra InnovaMass 240i Series Instruction Manual Download Page 63

63 

 

Navigate to the Diagnostics (Sub Menu).  Push the enter key 

 to reach the next lower level. Use 

the left 

 and right 

 buttons to reach the Low/High sub-menu. Hit the enter key 

 to reach the 

next lower level of menu.  Use the left 

 and right 

 buttons to move between menu screens 

under the Low/High sub-menu.   
 
 

Max Flow: 

The Max Flow menu displays the maximum recorded flow value along with the units.

 

 
 
 
 
 

Min Flow: 

The Min Flow menu displays the minimum recorded flow value along with the units.

 

 
 
 
 
 
 

 

 

For all meters, the maximum velocities are: liquids 30 fps (9.1 mps) and 
gases 300 fps (91.4 mps).   Exceeding these velocities may damage the 
temperature and velocity sensors, as well as other meter internals exposed to 
the process flow. 
 

 
 

Vmax: 

The Vmax menu displays the maximum recorded velocity value along with the units.

 

 
 
 
 
 

Vmin: 

The Vmin menu displays the minimum recorded velocity value along with the units.

 

 
 
 
 
 

Max Temp: 

The Max Temp menu displays the maximum recorded temperature value along with 

the units.

 

 
 
 
 
 

Min Temp: 

The Min Temp menu displays the minimum recorded temperature value along with 

the units.

 

 
 
 
 
 

Max Flow ft3/min 

130.3 

 

Min Flow ft3/min 

5.6 

 

Vmax 

24.565

 

Min Flow ft3/min 

1.0558

 

Max Temp C 

178.32 

 

Min Temp C 

-21.5 

 

Summary of Contents for InnovaMass 240i Series




















































































































Reviews:

No comments