manualshive.com logo in svg

Sierra InnovaMass 240i Series, Instruction Manual, Page: 106 / 115

Share
Download
Sierra InnovaMass 240i Series Instruction Manual Download Page 106

106 

 

NOTE

: Please insure that when you mount these cable glands they are made-up wrench tight. At 

least 3-1/2 turns of the thread must be engaged inside of the electronics enclosure. 

4.4.

 

Special Conditions for a Safe Use/Specific Conditions of Use 

The ambient temperature must never overrun the following limits: -20…+60°C. The surface 
temperature of the device (indicated on the device) must never exceed this temperature and must 
take into account both ambient and fluid temperatures. 
 
Consult the manufacturer if dimensional information on the flameproof joints is necessary.  
 
The flameproof joints of the equipment are not intended to be repaired.  Consult the manufacturer 
if repair of the flameproof joints is necessary. 
 
For probes longer than 13 inches, a suitably certified conduit sealing device is required to be 
installed between the main enclosure and the probe body.  The seal shall be located within 13 
inches of the main enclosure. 

4.5.

 

Particular Recommendations: Closing the Cover 

The safety is guaranteed as long as the covers are correctly screwed and locked. 
 
The lid locking screws are #10-24 Socket Head Cap Screws (SHC Screw) that use a 5/32-inch 
hex head wrench/driver to adjust. To lock the lids firmly tighten down/secure the lid and then 
back out the associated SHC screw firmly so that the lid is secured and locked in place. If one of 
the ribs/bumps on the lid happens to line up so it is blocking access to the SHC screw then either 
slightly tighten the lid more or loosen the lid slightly, just enough to gain access to the lid locking 
SHC screw. 

Note that this very minor adjustment, if necessary, does not affect the leak integrity of 

the enclosure

.  To un-lock the lid allowing for removal, just turn in the associated SHC screw so 

that it is no longer in contact with the lid, then the lid can be removed. There are two lids to be 
locked on the main enclosure and two lids to be locked on  the remote enclosure (If E4 feature 
was ordered) in order to maintain the safety ratings. 
 
 
 

Summary of Contents for InnovaMass 240i Series




















































































































Reviews:

No comments