manualshive.com logo in svg

Sierra InnovaMass 240i Series, Instruction Manual, Page: 27 / 115

Share
Download
Sierra InnovaMass 240i Series Instruction Manual Download Page 27

27 

 

main enclosure and two lids to be locked on the remote enclosure (if  E4 feature was ordered) 
enclosures in order to maintain the safety ratings.  
 
 

 

    
 
 

 

The following warnings should be obeyed: 
 

 
 
To minimize an electrostatic charging hazard on the exterior of the enclosures both the main and 
remote (if E4 option ordered) enclosures should be connected to earth ground, see below for more 
details. 
 

1.

 

Earthing

: The Sierra Instruments units must be connected to a good quality earth. The 

units are provided with internal and external earthing terminals.  

 

2.

 

External Earthing

: The external earthing connections are located on the boss on the 

outside of both the main housing and remote housing (E4 option if ordered) and consist 
of an 18-8SS pan head Phillips screw (10-24 UNC-2B thread) and a serrated tooth #10 
ring terminal for 16-14 AWG wire.  

 

3.

 

Internal Earthing

: The internal earthing connection is located in the main and remote 

(E4 option if ordered) housing terminal side and consist of an 18-8SS pan head Phillips 
screw (10-24 UNC-2B thread) and a serrated tooth #10 ring terminal for 16-14 AWG 
wire.  

 

 

 

 

DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS 

PRESENT  

 

DO NOT OPEN WHEN ENERGIZED 

 

POTENTIAL ELECTROSTATIC CHARGING HAZARD

—

SEE 

INSTRUCTIONS 

 

Figure 10. InnovaMass Main and Remote Enclosure Shown With Lid Locking Screw 

 

Summary of Contents for InnovaMass 240i Series




















































































































Reviews:

No comments