Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 42

Page: 42 / 196

Installing system components

3.4 Attaching the KTP Mobile wall-mounting bracket

TP1000F Mobile RO

Operating Instructions, 08/2017, A5E39831415-AA

3.4.3

Fasteneing the KTP Mobile wall-mounting bracket

Requirement

The requirements refer to the installation of the wall-mounting bracket to a control cabinet.

●

A level bolting surface

●

3 M5 bolts and a suitable screwdriver

●

3 M5 nuts and a suitable wrench

Procedure

1. Place the wall-mounting bracket level

on the mounting surface.

2. Mark the drill holes at the indicated

locations in the figure on the right.

3. Drill 3 holes for M5 type bolts based on

your mounting requirements.

4. Fasten the wall-mounting bracket with

the bolts and nuts.

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Search results

Summary of Contents for SIMATIC HMI TP1000F Mobile RO

Reviews:

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 42 / 196

Search results

Summary of Contents for SIMATIC HMI TP1000F Mobile RO

Reviews: