Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 175

Page: 175 / 196

Technical specifications

9.9 Connection box compact interfaces

TP1000F Mobile RO
Operating Instructions, 08/2017, A5E39831415-AA

175

9.9

Connection box compact interfaces

9.9.1

Position of the interfaces

The figure below shows the interfaces of the connection box compact with relevance for

commissioning.

①

Interface X1

②

Interface X10

9.9.2

Interface X1

RJ45 socket, 8-pin

Contact

Assignment

TD+

TD–

RD+

Not connected

RD–

Not connected

Note
LEDs on the RJ45 socket not active
The two LEDs at the RJ45 socket of the connection box compact are not supported by the

hardware and do not light up during operation.

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Search results

Summary of Contents for SIMATIC HMI TP1000F Mobile RO

Reviews:

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 175 / 196

Search results

Summary of Contents for SIMATIC HMI TP1000F Mobile RO

Reviews: