manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 122 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 122

Parameterizing the Mobile Panel 

 

5.13 Functions for service and commissioning 

 

TP1000F Mobile RO 

122

 

Operating Instructions, 08/2017, A5E39831415-AA  

7.

 

To delete the file selected, press "Delete". 
The Delete confirmation dialog is displayed. The file is deleted when you select "OK". 

8.

 

To restore the data from the selected file, select "Restore". 
The following dialog appears: 

 

9.

 

Selecting "Yes" restores the data. 

The "Transfer" dialog appears. A progress bar shows the status of the restore process. 

When the restore operation is complete, the "Restore operation successfully completed." 

message is displayed. The HMI device then restarts and remains in transfer mode. 

10.

 

Remove the storage medium, if necessary. 

The data from the storage medium is now restored on the HMI device. 

 

 

Note 
After restoring, a recalibration of the touch screen may be required, see also section 

"Calibrating the touch screen (Page 85)". 

 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments