manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 30 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 30

Safety instructions 

 

2.2 Notes about usage 

 

TP1000F Mobile RO 

30

 

Operating Instructions, 08/2017, A5E39831415-AA  

2.2

 

Notes about usage 

 

 

NOTICE 
HMI device approved for indoor use only 
The HMI device may be damaged if operated outdoors. 
Operate the HMI device indoors only. 

 

 

Note 
Using an Ethernet data transmission rate of 100 Mbps 
The Ethernet data transmission rate of 10 Mbps is not supported by Mobile Panels 2nd 

Generation. 
Use a data transmission rate of 100 Mbps for communication with the device. 

 

Industrial applications 

The HMI device is designed for industrial applications. It conforms to the following standards: 

●

 

Requirements for emitted interference EN 61000-6-4 +A1 

●

 

Requirements for interference immunity EN 61000-6-2 

Use in residential areas 

 

 

Note 
The HMI device is not intended for use in residential areas. The operation of HMI devices in 

residential areas can cause interference to radio and television reception. 

 

If the HMI device is used in a residential area, you must take measures to achieve Limit 

Class B conforming to EN 55011 for RF interference. 
A suitable measure for achieving the RF interference level to Limit Class B, for example, is 

the use of filters in power supply lines. 
Individual acceptance is required for these measures.  

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments