manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 34 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 34

Safety instructions 

 

2.5 Important notes for the enabling mechanism 

 

TP1000F Mobile RO 

34

 

Operating Instructions, 08/2017, A5E39831415-AA  

 

NOTICE 
Enabling button must not be fixed 
Fixing the enabling button in one of its positions can cause malfunctions in the fail-safe 

automation system. 
Make sure that the enabling button is not being held permanently in any of its positions. 

 

 

Note 
The enabling button is effective when the HMI device is connected to a connection box. The 

following applies: 

•

 

"E-stop button evaluated by safety relay" operating mode 

The emergency stop button is lit. 

•

 

"Stop button evaluated by safety relay" operating mode 

The emergency stop / stop button is not lit with this operating mode.. 

 

 

Note 
Removing a discrepancy error 
The enabling button has two channels. Both contacts must be closed at the same time for 

the "enable" and "panic" switch positions. A discrepancy error is generated if one of the 

contacts is open while the other is closed. When a discrepancy error occurs, enabling is no 

longer possible. To reactivate enabling, press the enabling button once completely into the 

"panic" position and then release it. 

 

See also 

Operating the enabling button (Page 67) 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments