Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 111

Page: 111 / 196

Parameterizing the Mobile Panel

5.11 Configuring network operation

TP1000F Mobile RO
Operating Instructions, 08/2017, A5E39831415-AA

111

5.11

Configuring network operation

5.11.1

Overview

Addressing computers

Computers are usually addressed using computer names within a PROFINET network.

However, the network address is set with RemoteOperate.
Determine the following parameters:

●

Is DHCP used in the local network for dynamic assignment of addresses?

If not, get a TCP/IP address for the HMI device.

●

Which TCP/IP address does the default gateway have?

●

If a DNS network is used, what is the address of the name server?

●

If a WINS network is used, what is the address of the name server?

Configuration includes:

●

Specifying the computer name of the HMI device

●

Specifying the IP address and name server

●

Specifying the logon data

NOTICE
RemoteOperate connection overwrites network parameters
When you start RemoteOperate and connect the client to a server in the server selection

list, RemoteOperate overwrites the network parameters with the stored properties of the

server connection. If another application needs the network parameters for a network

connection, note the following:

•

Note down the network parameters of the application.

•

After the start, exit RemoteOperate and re-configure the network.

•

Alternatively, select a shared IP address and subnet mask for RemoteOperate and your

application.

Parameterization is described from section "Specifying the computer name of the HMI device

(Page 112)" on.

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Search results

Summary of Contents for SIMATIC HMI TP1000F Mobile RO

Reviews:

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 111 / 196

Search results

Summary of Contents for SIMATIC HMI TP1000F Mobile RO

Reviews: