manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 24 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 24

Overview 

 

1.9 Organizational measures 

 

TP1000F Mobile RO 

24

 

Operating Instructions, 08/2017, A5E39831415-AA  

1.9

 

Organizational measures 

Measures 

If you are using a fail-safe Mobile Panel in a fail-safe system, you must consider the 

following organizational measures: 

●

 

Install stationary emergency stop or emergency off buttons in the plant that are effective 

independent of the Mobile Panel. 

●

 

Perform a risk analysis of the plant. 

●

 

If the overall plant is not to be monitored from a single location, configure plant areas. 

●

 

Select the same operating mode for all connection boxes in a contiguous plant area. 

●

 

Create a safety program. 

●

 

Run an acceptance test on the fail-safe automation system. 

F-systems 

The table below shows the F-systems that can be configured or installed for a given 

connection box. Requirement is that you are using a fail-safe Mobile Panel. 

 

Connection box 

Hardwired F-system, no emergency 

stop/stop bypass 

Hardwired F-system with emergency 

stop/stop bypass 

compact 

Yes 

No 

standard 

Yes 

No 

advanced 

No 

Yes 

Safety-related 

operating mode 

Stop button evaluated by safety relay 

Stop button evaluated by safety relay 

E-stop button evaluated by safety relay  E-stop button evaluated by safety relay 

1.10

 

Mobile Panel and connection box compatibility 

The Mobile Panels 2nd Generation are not compatible with the connection box DP Basic and 

connection box DP Plus. 

Compatibility of Mobile Panels 2nd Generation – connection box PN Basic and PN Plus 

The TP1000F Mobile RO is compatible with the following connection boxes: 

●

 

Connection box PN Basic, article number 6AV6671-5AE01-0AX0 

●

 

Connection box PN Plus, article number 6AV6671-5AE11-0AX0 

Restrictions: 

●

 

Only one hardwired F-system with a stop function and enabling function is permitted. 

 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments