Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 93

Page: 93 / 112

Technical data

8.5 Switching properties

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

8.5

Switching properties

The properties listed below apply to the SCALANCE XR-500.

Table 8- 1

Switching properties

Max. number of learnable ad-

dresses

16 000

Aging time

Can be configured (default value: 40 seconds)

Switching technique

Store&Forward

Latency

25-70 microseconds

Table 8- 2

Reconfiguration times for redundancy mechanisms

Redundancy mechanism

Reconfiguration times in ms

HRP

300

Standby link

300

MRP

200

Table 8- 3

Full wire speed switching

Number of frames per second

At a frame length of

At 100 Mbps

At 1000 Mbps

For 10 Gbps

148810

1488095

14880952

64 bytes

84459

844595

8445946

128 bytes

45290

452899

4528986

256 bytes

23496

234962

2349664

512 bytes

11973

119732

1197318

1024 bytes

9615

96154

961538

1280 bytes

8127

81274

811688

1518 bytes

Note
The following applies for SCALANCE XR-500:
The number of SCALANCE XR-500 modules connected in a line influences the frame delay.

When a frame passes through the switch, this is delayed by the Store&Forward function of

the SCALANCE XR-500 by 25-70 microseconds (at 1000 Mbps).

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands