Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 48

Page: 48 / 112

Assembling

4.6 Plugging and pulling MM900 media modules

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

Identification of the media module slots and ports

Below, you can see the arrangement of the slots and ports of a SCALANCE XR552-12M:

Slot

Port

Slot

Port

Slot

Port (SFP+)

Slot

Port

Slot

Port

A SCALANCE XR528-6M has a total of six slots and four SFP+ ports.

Note
Slot number
In modular devices, the MM900 media modules can be assigned a slot number. The labels

for the slot numbers ship with the modular devices.
SFP+ ports in slot 0
The SFP+ ports in slot 0 are part of the basic device.

Plugging in media module

Figure 4-3

Plugging a media module into a SCALANCE XR552-12M. SCALANCE XR528-6M is

used analogously.

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands