Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 57 | Manualshive

Page: 57 / 112

background image

Connecting

5.1 Commissioning

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

57

NOTICE
Failure of the data traffic due to contamination of optical plug-in connections
Optical sockets and plugs are sensitive to contamination of the end face. Contamination

can lead to the failure of the optical transmission network.
Close unused optical sockets and plugs as well as pluggable transceivers and slots with the

supplied protective caps.
Remove the protective caps only immediately before you use the plug-in connection.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD
Do not connect or disconnect cables to or from the device when a flammable or

combustible atmosphere is present.

Safety notices for use according to ATEX and IECEx
If you use the device under ATEX or IECEx conditions you must also keep to the following

safety notices in addition to the general safety notices for protection against explosion:

WARNING

Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

Safety notices when using the device according to Hazardous Locations (HazLoc)
If you use the device under HazLoc conditions you must also keep to the following safety

notices in addition to the general safety notices for protection against explosion:

WARNING

EXPLOSION HAZARD
You may only connect or disconnect cables carrying electricity when the power supply is

switched off or when the device is in an area without inflammable gas concentrations.

«
...
55
56
57
58
59
...
»

Summary of Contents for SCALANCE XR-500

















































































































Reviews:

No comments

Related manuals for SCALANCE XR-500

Brand: CALIENT Pages: 46

Brand: CALIENT Pages: 42

Brand: Perel Pages: 4

Brand: Ask Pages: 4

S12500G-AF Series

Brand: H3C Pages: 105

Brand: WAGO Pages: 36

Brand: Watchguard Pages: 26

CT.TS005.003902

Brand: Talkswitch Pages: 309

Brand: TAXON TOOLS Pages: 9

Brand: Hamlet Pages: 2

Brand: GeoVision Pages: 7

Brand: Omron Pages: 6

Brand: Xcellon Pages: 2

Brand: Fastcabling Pages: 4

Brand: Ocean Matrix Pages: 6

Brand: Kramer Pages: 8

BZ-UHD-88M100-ARC

Brand: BZB Gear Pages: 42

Brand: H3C Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands