Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 39

Page: 39 / 112

Assembling

4.1 Safety notices for installation

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

WARNING

The device may only be operated in an environment with pollution degree 1 or 2 (see IEC

60664-1).

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I,

Zone 2, the device must be installed in a cabinet or a suitable enclosure.

Safety notices for use according to ATEX and IECEx
If you use the device under ATEX or IECEx conditions you must also keep to the following

safety notices in addition to the general safety notices for protection against explosion:

WARNING

To comply with EC Directive 2014/34/EU (ATEX 114) or the conditions of IECEx, this

enclosure or cabinet must meet the requirements of at least IP54 in compliance with EN

60529.

Safety notices when using the device as industrial control equipment according to UL 61010-

2-201
If you use the device under UL 61010-2-201 conditions you must also keep to the following

safety notices in addition to the general safety notices for protection against explosion:

WARNING

The devices are "open equipment" acc. to the standard UL 61010-2-201. To fulfill

requirements for safe operation with regard to mechanical stability, flame retardation,

stability, and protection against contact, the following alternative types of installation are

specified:

•

Installation in a suitable cabinet.

•

Installation in a suitable enclosure.

•

Installation in a suitably equipped, enclosed control room.

WARNING

If the cable or housing socket exceeds 70 °C or the branching point of the cables exceeds

60 °C, special precautions must be taken. If the equipment is operated in an air ambient in

excess of 40 °C, only use cables with admitted maximum operating temperature of at least

℃.

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands