Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 76

Page: 76 / 112

Upkeep and maintenance

7.1 Changing the fan unit

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

Procedure

Follow the steps below to replace the fan unit:
1.

Unlock the door in the housing by pushing the catch to the right with a slotted screwdriver

①

Figure 7-1

Opening the housing of a SCALANCE XR552-12M. SCALANCE XR528-6M is used

analogously.

Open the door in the housing

②

WARNING

Danger of injury by touching rotating fan blades
There is a risk of injury if you touch rotating fan blades.
Do not touch rotating fan blades.
Allow the fan blades to come to a stop.

Pull the fan unit out of the housing using the handle on the fan unit

③

. Note that the filter

frame with the filter mat is also automatically pulled out.

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands