Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 54

Page: 54 / 112

Assembling

4.8 Mounting power supply units

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

Procedure

Figure 4-5

Rear panel mounting of the SCALANCE XR552-12M. SCALANCE XR528-6M is used

analogously.

On the rear panel of an IE switch, there are sockets for the direct connection of a maximum

of two PS598-1 power supply units. On the rear of the PS598-1 power supply unit there is a

corresponding plug.
To mount the PS598-1 power supply unit on the rear panel of an IE switch, follow the steps

below:
1.

Fit the PS598-1 power supply unit and the IE switch together

①

The two devices are equipped with positioning elements that must engage during

installation and protect the plug from excessive bending strain.

Screw the two devices to the mounting plates supplied with the main device

②

The maximum tightening torque of the screws is 0.5 Nm.

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands