Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 105

Page: 105 / 112

Certification

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

105

The SIMATIC NET products meet the requirements of the EC directive 94/9/EC "Equipment

and Protective Devices for Use in Potentially Explosive Atmospheres”. and as of 20.04.2016

the EC directive 2014/34/EU.
ATEX classification:
II 3 G Ex nA IIC T4 Gc
KEMA 07ATEX0145 X
The products meet the requirements of the following standards:

●

EN 60079-15 (electrical apparatus for potentially explosive atmospheres; Type of

protection "n")

●

EN 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)

You will find the current versions of the standards in the currently valid ATEX certificates.

Note
Only variants with 24 VDC power supply meet the requirements of this approval.

IECEx

The SIMATIC NET products meet the requirements of explosion protection according to

IECEx.
IECEx classification:
Ex nA IIC T4 Gc
DEK 14.0025X
The products meet the requirements of the following standards:

●

IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of

protection "n")

●

IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)

You will find the current versions of the standards in the currently valid IECEx certificates.

Note
Only variants with 24 VDC power supply meet the requirements of this approval.

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands