Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 78

Page: 78 / 112

Upkeep and maintenance

7.2 Changing the filter pad

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

7.2

Changing the filter pad

The following devices have a filter pad:

●

SCALANCE XR528-6M

●

SCALANCE XR552-12M

NOTICE
Damage to the device due to inadequate ventilation
A badly contaminated filter reduces air flow and can cause the device to be damaged.
Check the degree of contamination of the filter regularly and clean or replace the filter mat

as necessary.

Procedure

Follow the steps below to replace the filter pad:
1.

Unlock the door in the housing by pushing the catch to the right with a slotted screwdriver

①

Figure 7-3

Opening the housing of a SCALANCE XR552-12M. SCALANCE XR528-6M is used

analogously.

Open the door in the housing

②

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands