Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 109

Page: 109 / 112

Certification

10.2 Mechanical stability (in operation)

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

109

WARNING

Personal injury and property damage can occur
The installation of expansions that are not approved for SIMATIC NET products or their

target systems may violate the requirements and regulations for safety and electromagnetic

compatibility.
Only use expansions that are approved for the system.

Note
The test was performed with a device and a connected communications partner that also

meets the requirements of the standards listed above.
When operating the device with a communications partner that does not comply with these

standards, adherence to the corresponding values cannot be guaranteed.

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands