Siemens SCALANCE W738-1 M12 Page 31 Configuration Manuals Download

Page: 31 / 616

2.6.2

Address types, address ranges and address masks

Overview

Since the various types of addresses can be represented by different notations, the notations

used in the Command Line Interface are shown below:
● IPv4 addresses

An IPv4 address consists of 4 bytes. Each byte is represented in decimal, with a dot

separating it from the previous one, refer to the section "Structure of an IPv4 address

(Page 34)"

Note
With leading zeros, the numbers are interpreted as octal numbers, e.g.: 192.168.070.071

→ 192.168.56.57.

● IPv6 addresses

IPv6 addresses consist of 8 fields each with four-character hexadecimal numbers (128 bits

in total). The fields are separated by a colon, refer to the section "Structure of an IPv6

address (Page 36)".

● Network masks

A network mask is a series of bits that describes the network part of an IPv4 address.

The notation is normally decimal in keeping with the IPv4 address.

● Alternative notation for network masks

In contrast to the notation described above, network masks can also be represented as a

number of 1 bits. The mask of the decimal representation 255.255.0.0 is then written as /16.

The syntax is then for example: <ipaddress> / 16

Note that there must be a space before and after the "/".

● MAC addresses
● In the syntax of the Command Line Interface, a MAC address is represented as a sequence

of 6 bytes in hexadecimal format, in each case separated by a colon.

The syntax is then, for example: aa:aa:aa:aa:aa:aa

● Multicast addresses

Layer 2 multicast addresses as used on this device use the notation of MAC addresses.

For permitted address ranges, check the rules or ask your network administrator.

Description

2.6 Interface identifiers and addresses

SCALANCE W770/W730 acc. to IEEE 802.11n Command Line Interface

Configuration Manual, 09/2017, C79000-G8976-C324-08

Summary of Contents for SCALANCE W738-1 M12









































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SCALANCE W738-1 M12

Reviews:

Related manuals for SCALANCE W738-1 M12

Brands by name

Popular brands

Siemens SCALANCE W738-1 M12, Configuration Manuals

Search results

Summary of Contents for SCALANCE W738-1 M12

Reviews:

Related manuals for SCALANCE W738-1 M12

Brands by name

Popular brands