Siemens OpenStage 40 HFA HiPath 4000 Operation Manual Download

Page: 27 / 120

Making Calls – Basic Functions

Step by step

Making Calls – Basic Functions

Answering calls

Answering a call via the handset

The phone is ringing. The caller is displayed.

Lift the handset.

if nec.

Set the call volume.

Answering a call via the loudspeaker
(speakerphone mode)

The phone is ringing. The caller is displayed.

Press the key shown. The LED key lights up.

The speakerphone function is activated.

if nec.

Set the call volume.

Suggestions for using speakerphone mode:

•

Tell the other party that speakerphone mode is ac-
tive.

•

Adjust the call volume while speakerphone mode is
active.

•

The ideal distance between the user and the phone
in speakerphone mode is 50 cm.

Please read the introductory chapter "Getting to
know your OpenStage phone"

page 11

care-

fully before performing any of the steps descri-
bed here on your phone.

An incoming call will cancel any ongoing telepho-
ne setting operations.

Summary of Contents for OpenStage 40 HFA HiPath 4000

























































































































Search results

Summary of Contents for OpenStage 40 HFA HiPath 4000

Reviews:

Related manuals for OpenStage 40 HFA HiPath 4000

Brands by name

Popular brands

Siemens OpenStage 40 HFA HiPath 4000, Operation Manual

Search results

Summary of Contents for OpenStage 40 HFA HiPath 4000

Reviews:

Related manuals for OpenStage 40 HFA HiPath 4000

Brands by name

Popular brands