Siemens NK8237 IEC 60870-5-104 Installation, Configuration And Commissioning Download Page 74

Page: 74 / 80

Maintenance and diagnostics
The NW8204 diagnostic tool

74
Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

Configuring the log upload

Uploading log data

Note: If the data upload procedure seems to take too long to be accomplished,

you can abort the procedure by clicking the Abort Log Upload button.

Note: The log file can be imported as CSV file to a spreadsheet application to be

analyzed by expert users (Technical Support).

Changing the active mass storage device on the fly

If two mass storage devices are available on your system (USB and SD card), you

can change on the fly the active storage device. Proceed as follows:
1. Right-click the inactive mass storage device you want to be active.
2. Select Set as Log storage.



The active mass storage device is graphically identified by a floppy disk icon.

Setting the log storage

Summary of Contents for NK8237 IEC 60870-5-104

















































































Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands

Siemens NK8237 IEC 60870-5-104, Installation, Configuration And Commissioning

Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands