Siemens NK8237 IEC 60870-5-104 Installation, Configuration And Commissioning Download Page 70

Page: 70 / 80

Maintenance and diagnostics
The NW8204 diagnostic tool

70
Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

Click this button to display the Port Number dialog box:

Port number request

A possible port number to check is 2404 (IEC).
Click OK to check the port number. At that point, the associated field displays the

type of information found (for example, Last IP connected) and you can to use the

field arrow controls to display the current IP address.

Note: If the IP address is

‘0.0.0.0’, no PC was connected to that port.

Read HW version
Read the NK8237 hardware version (NKM8001-A1, NKM8001-A2

, …).

Note: NK8237 MP4.40 or later firmware is required.

Read PIC24FW Ver
Read the PIC24 microcontroller firmware version.

Note: NK8237 MP4.40 or later firmware is required.

Read WDT Status
Read the NK823x watchdog status (enabled or disabled).

Note: NK8237 MP4.40 or later firmware is required.

Read Mass Storage
Read the mass storage device (USB mass storage device or SD card) available on

the NK8237 unit. Right-click the icon of the connected mass storage device (the

icons display in the box on the right) to display the available commands:

⚫

Show info: show information about the connected mass storage device.

⚫

Unmount: command needed to safely remove the mass storage device.

⚫

Set as Log storage: set the selected device (USB mass storage device or SD

card, if both are available on the system) as the active storage device.

Set Default Log
Restore the NK8237 log settings as set in Composer.
Protocol Info
Open the NK Protocols window, which allows configuring the NK8237 logging on

the fly (see

Using log files [➙

73]).

Read Logging Status
Read the NK8237 logging status: Active, Inactive, and Active (Modified) once on

the fly configuration changes have been set.
Read Firewall Status

Summary of Contents for NK8237 IEC 60870-5-104

















































































Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands

Siemens NK8237 IEC 60870-5-104, Installation, Configuration And Commissioning

Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands