Siemens NK8237 IEC 60870-5-104 Installation, Configuration And Commissioning Download Page 27

Page: 27 / 80

Hardware installation

NK8237 hardware installation

Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

X102: Onboard I/O (Inputs)

Onboard I/O (inputs).

Assignment

Input 1 (Mains failure)

Input 2 (Battery fault)

Input 3 (Power supply fault)

Common

+ Val

–

Val

COM 1, COM 2: RS232 Connectors

RS232 lines are connected to 9pin D-Sub connectors, female type.

RS232 connections.

Assignment

RXD

TXD

DTR

GND

DSR

RTS

CTS

DIN Rail Installation

The modules are supplied in a plastic box that can be easily attached to the DIN

rail by hooking it on the top of the rail and pressing it in on the opposite side. To

detach the box, pull downward on the tab located at the rear of the module. The I/O

modules are mounted the same way.

Note: Before removing the box, carefully disconnect the flat cable (bus) of the I

module, as well as the power supply cables.

Installation in Subsystem Housing Without DIN-Rail

NK8237 can be installed without the plastic box into the control unit cabinet. In this

case, the NKA8011-A1 mounting plate may be needed.

Summary of Contents for NK8237 IEC 60870-5-104

















































































Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands

Siemens NK8237 IEC 60870-5-104, Installation, Configuration And Commissioning

Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands