Siemens NK8237 IEC 60870-5-104 Installation, Configuration And Commissioning Download Page 66

Page: 66 / 80

Maintenance and diagnostics
The NW8204 diagnostic tool

66
Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

NW8204 window (installed GUI)

2. Insert the NK IP Address.

Note: Inserting an incorrect IP address causes the following window to display.

If you are notified by this message, click OK and enter again the IP Address. If
you want to enter the NK8237 default IP address 192.168.9.41, you can use
the menu Set Default IP Address instead of manually enter it.

3. Select Open Connection.

Note: You can select the FTP Mode: Active (default) or Passive (needed if a

firewall is active in the PC).



NW8204 opens an FTP session on the NK8237 and lists all files available

on the NK8237 flash disk.

Summary of Contents for NK8237 IEC 60870-5-104

















































































Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands

Siemens NK8237 IEC 60870-5-104, Installation, Configuration And Commissioning

Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands