Siemens NK8237 IEC 60870-5-104 Installation, Configuration And Commissioning Download Page 16

Page: 16 / 80

Structure and functions
NK8237 hardware

16
Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

Structure and functions

6.1

NK8237 hardware

The NK8237 is composed of an electronic board installed in a compact and robust

plastic box.

Note: NK8237 units with build state up to 01 are equipped with the NKM8001-A1

mainboard and NK8237 units with build state 10 or higher are equipped with the

NKM8001-A2 mainboard.

NK8237 gateway unit

6.1.1

Front panel

The front panel houses 9 LEDs.

Left Side LEDs

The five LEDs on the left side are from top to bottom:
Power (green LED)
Power (hardware

–

controlled).

Vital functions (green LED)
Software vitality:

⚫

Blinking (1 flash)

: core software running.

⚫

Blinking (2 flashes)

: core software running and logging function active.

Tamper (bi-color LED)
Unit tamper:

⚫

Red

means tamper alarm (hardware controlled).

⚫

Green

means tamper disabled (from management station).

Download (red LED)
Network diagnostics:

⚫

Off

: status OK.

⚫

Blinking (1 flash)

: missing identification from NS8xxx.

⚫

Blinking (2 flashes)

: not used.

⚫

Blinking (3 flashes)

: FTP channel open (default mode; for switch settings see

Internal DIP Switches

⚫

: critical/hardware fault.

Summary of Contents for NK8237 IEC 60870-5-104

















































































Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands

Siemens NK8237 IEC 60870-5-104, Installation, Configuration And Commissioning

Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands