Siemens NK8237 IEC 60870-5-104 Installation, Configuration And Commissioning Download Page 46

Page: 46 / 80

Configuration
Creating the NK8237 Gateway

46
Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

Routing table configuration (from MP4.81-02, the Enable dynamic routing (OSPF) option is

no longer supported)

Checking the routing table



The configuration has been downloaded to the NK8237 unit.

1. Select the NK8237 node.
2. In the Routing tab, click the Get Info button to upload the routing configuration

from the selected NK8237 unit.

–

The updated information populates the list in the Routing Info section.

3. Check that the uploaded table actually matches the configured table.

Inconsistencies will indicate a configuration error or network problems.



At this point, you can be sure that the unit can access the external subnets

over the configured routes.

Note: Use the Ping button in the Tools tab to check the actual connectivity

between the unit and IP devices on the subnets.

Summary of Contents for NK8237 IEC 60870-5-104

















































































Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands

Siemens NK8237 IEC 60870-5-104, Installation, Configuration And Commissioning

Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands