Siemens NK8237 IEC 60870-5-104 Installation, Configuration And Commissioning Download Page 67

Page: 67 / 80

Maintenance and diagnostics

The NW8204 diagnostic tool

Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

NW8204 window with open connection (installed GUI)

Item

Name

Description

Change User

Select to display the user login window (see step 1).

About

Displays the version of the NW8204 tool.

Local File

Browse for a local copy of DIAGNO.LOG or

EEPROM.LOG to analyse/troubleshoot a remote NK82xx

(admin user only).

Set Default IP

Address

See step 2.

Send Default

Configuration File

(Deprecated. Do not use.)

History log frame

—

Error log frame

—

Download/Upload

progress status.

Transferred Bytes, Percent, and Byte/Sec rate.

Note: If you do not close the connection, you will be automatically timed out in five

minutes.

Summary of Contents for NK8237 IEC 60870-5-104

















































































Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands

Siemens NK8237 IEC 60870-5-104, Installation, Configuration And Commissioning

Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands