Siemens NK8237 IEC 60870-5-104 Installation, Configuration And Commissioning Download Page 17

Page: 17 / 80

Structure and functions

NK8237 hardware

Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

Diagnostics (yellow LED)
Internal interface diagnostics:

⚫

Off

: status OK.

⚫

Blinking (fast)

: booting operating system after restart.

⚫

Blinking (1 flash)

: missing or insufficient license.

⚫

Blinking (2 flashes)

: trouble with the I

C bus to I/O modules.

⚫

Blinking (3 flashes)

: not used

⚫

Blinking (4 flashes)

: trouble with the serial/network interface.

⚫

Blinking (5 flashes)

: trouble with DLL or RCLOCK file(s).

⚫

Blinking (6 flashes)

: IEC GW trouble.

–

SW trouble.

–

No communication to FS20/FS720 or to the IEC Master.

⚫

: critical/hardware fault.

Right Side LEDs

The four LEDs on the right side are, from top to bottom:

Name

Function

Com1

Status Com1

Red: RX

Green: TX

Com2

Status Com2

Com3 (not used)

Status Com3

Com4 (not used)

Status Com4

6.1.2

Internal DIP switches

The internal DIP switches (S101) enable a download session via FTP using a

default IP address.

Internal switch

Functions

DIP switch 1

Default mode/network access: If DIP switch 1 is ON, a Secure Download

connection occurs by default on the Ethernet 1 at the default IP address

192.168.9.41.

DIP switch 2

Default mode/network access: If DIP switch 2 is ON, a Secure Download

connection occurs by default on the Ethernet 2 at the default IP address

192.168.10.41.

Summary of Contents for NK8237 IEC 60870-5-104

















































































Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands

Siemens NK8237 IEC 60870-5-104, Installation, Configuration And Commissioning

Search results

Summary of Contents for NK8237 IEC 60870-5-104

Reviews:

Related manuals for NK8237 IEC 60870-5-104

Brands by name

Popular brands