Siemens MOBILETT XP Instructions For Use Manual Download Page 77

Page: 77 / 109

Cleaning and Disinfecting

MOBILETT
SPR8-230.621.01.03.02

of 106

Cleaning and Disinfecting

The MOBILETT shall be disconnected from the mains and switched off before it
is cleaned or disinfected.

Cleaning

Do not use any abrasive detergents (because of material intolerance) or cleaning
agents containing solvents (e.g. cleaning solutions, alcohol, stain remover).

◆

Wipe the MOBILETT with a cloth moistened with water or a lukewarm, diluted
aqueous solution of a household dish washing liquid.

Cleaning of DAP chamber (Option)

◆

Wipe the MOBILETT with a cloth moistened with water or a lukewarm, diluted
aqueous solution of a household dish washing liquid.

Caution

The cleaning fluid has penetrated into the equipment!

The MOBILETT is damaged

◆

Do not spray the equipment.

Caution

High voltage inside the DAP ionization chamber!

The DAP ionization chamber is very sensitive

◆

Be sure to use a soft cloth to avoid scratching the chamber.

Summary of Contents for MOBILETT XP














































































































Search results

Summary of Contents for MOBILETT XP

Reviews:

Related manuals for MOBILETT XP

Brands by name

Popular brands

Siemens MOBILETT XP, Instructions For Use Manual

Search results

Summary of Contents for MOBILETT XP

Reviews:

Related manuals for MOBILETT XP

Brands by name

Popular brands