Siemens FDA221 Technical Manual Download Page 52

Page: 52 / 114

Mounting / Installation
Preparatory work

52
Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

Removing the housing cover



The housing is free from dust.



Do not disconnect the connection cable running between the housing cover

and the back box.

1. Remove the two screws on the top of the aspirating smoke detector using a

size 2 Phillips screwdriver (step 1).

2. Slide the housing cover in the direction of the arrow until it snaps into place

(step 2).



The housing cover is open.



Opening of the housing is logged in the modification memory.



The

fault indicator flashes and the buzzer is switched on.



The relay outputs remain active and the 4…20 mA analog output has been

switched to fault (0.5 mA).

3. Press the

button to switch off the buzzer.



The relay outputs are deactivated.



The 4…20 mA analog output remains on fault.

4. Take hold of the housing cover on the left and right (A) and pull the side walls

apart (step 3).

5. Lift the housing cover off the back box (B). When doing this, be aware of the

connection cable (step 3).



The housing cover is removed.

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands