Siemens FDA221 Technical Manual Download

Page: 64 / 114

Mounting / Installation
Installation

64
Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

5.3

Installation

CAUTION

Electrical voltage on lines
Risk of injury due to electric shock

●

During mounting and installation work, electrical voltage must not be applied

to the lines.

Note the positive and negative poles.
Only connect one wire per terminal. This is the only way to ensure the connection

is failure-free for the entire service life of the device.

5.3.1

Connecting the external power unit

Two connection terminals are available for the aspirating smoke detector's power

supply. This allows more aspirating smoke detectors to be connected to a power

unit.
Prerequisite: The power unit used satisfies the requirements according to the

'External power unit and batteries' chapter.

Connection diagram for 'one aspirating smoke detector on one power

unit'

Connection without forwarding to other aspirating smoke detectors

Connection diagram for 'multiple aspirating smoke detectors on one

power unit'

Connection with forwarding to other aspirating smoke detectors

IN Connection of external power unit

OUT Connection for the power supply of other aspirating smoke detectors

Properties



Protected against polarity reversal



Connection of more aspirating smoke detectors

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands