Siemens FDA221 Technical Manual Download

Page: 68 / 114

Mounting / Installation
Installation

68
Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

5.3.3

Configurable 'GPI' input

Configurable input for an external switch. The setting is made in the 'Relay and

GPI' menu with the '

FXS2051

ASD Configuration Tool' software.

Monitoring for open line

Monitoring for short circuit and open line

Properties



Can be configured to trigger the following actions:

– Switching to Manned/Unmanned (not possible when fire control panel

FC20xx/FC72x is connected)

–  Resetting
–  Activating blowing-out unit
–  Deactivates all relays and alarm outputs



Monitoring for open line (1 resistor)



Monitoring for short circuit and open line (2 resistors)



Input for error monitoring on the external power unit

5.3.4

'Purge' relay output for blowing out (with FDA241 only)

Relay output for controlling an external blowing-out unit.

Connection: n.o.

Properties



Suitable for controlling an external blowing-out unit.



Configuration of:

– Purge interval
– Purge duration

When the aspirating smoke detector is in operation, the setting is made on the

FDnet/C-NET using the fire control panel configuration software.



For fire control panels FC20xx: 'SintesoWorks'



For fire control panels FC72x: 'Cerberus-Engineering-Tool'

When the aspirating smoke detector is in standalone operation, the setting is made

in the 'Purge' menu with the '

FXS2051

ASD Configuration Tool' software.

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands