Siemens FDA221 Technical Manual Download

Page: 55 / 114

Mounting / Installation

Preparatory work

Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

5.1.5

Installation position and space requirements

Installation site requirements



Only to be installed within a building where the ambient conditions are

permissible



No direct sunlight



Take into account the additional space required by and the need to access the

following:
–  External power unit and batteries
–  Blowing-out unit (optional)
–  Water trap (optional)



The aspirating smoke detector can be installed either horizontally or vertically

on a level surface.



The dust load should be low at the installation site, because the aspirating

smoke detector housing is opened for maintenance purposes.



Ensure that there is at least 150 mm of free space on each side of the installed

aspirating smoke detector to ensure the pipe system and electrical connections

can be installed with ease.

Connecting to the pipe system

The aspirating smoke detector can be installed in different installation locations.

The installation location to be used depends on the pipe system's connection to the

aspirating smoke detector.

Aspirating smoke detectors with different installation locations

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands