Siemens FDA221 Technical Manual Download

Page: 62 / 114

Mounting / Installation
Mounting

62
Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

5.2.4

Installing communication transponder FDCC221S

Communication transponder FDCC221S may only be installed if the aspirating

smoke detector is connected to FDnet/C-NET. Installation is not permitted in the

case of standalone operation.
Communication transponder FDCC221S has its own ID. The ID of communication

transponder FDCC221S is made visible to the detector line and it replaces the ID

of the aspirating smoke detector.

Installing communication transponder FDCC221S in an aspirating smoke detector

Changes on the type plate when the FDCC221S is installed

1  Mark indicating that the FDCC221S is installed
2  ID adhesive label from FDCC221S for aspirating smoke detector
3  Tear-off adhesive label for installation plan

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands