Siemens FDA221 Technical Manual Download

Page: 16 / 114

Safety
Standards and directives complied with

16
Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

2.3

Standards and directives complied with

A list of the standards and directives complied with is available from your Siemens

contact.

2.4

Release Notes

Limitations to the configuration or use of devices in a fire detection installation with

a particular firmware version are possible.

WARNING

Limited or non-existent fire detection
Personal injury and damage to property in the event of a fire.

●

Read the 'Release Notes' before you plan and/or configure a fire detection

installation.

●

Read the 'Release Notes' before you carry out a firmware update to a fire

detection installation.

NOTICE

Incorrect planning and/or configuration
Important standards and specifications are not satisfied.
Fire detection installation is not accepted for commissioning.
Additional expense resulting from necessary new planning and/or configuration.

●

Read the 'Release Notes' before you plan and/or configure a fire detection

installation.

●

Read the 'Release Notes' before you carry out a firmware update to a fire

detection installation.

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands