Siemens FDA221 Technical Manual Download

Page: 77 / 114

Configuration

Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

Configuration

The aspirating smoke detector can be configured in two ways:



Via the fire control panel and using the configuration software for the

FS20/FS720 (with limited configuration options)



Using the '

FXS2051

ASD Configuration Tool' software

Values whose parameters were set from the fire control panel cannot be changed

with the '

S2051 ASD Configuration Tool' software. They are only displayed in

the '

FXS2051

ASD Configuration Tool' software.

A detector-dependent password must be entered locally on the aspirating smoke

detector to obtain writing rights on the aspirating smoke detector with the

FXS2051

ASD Configuration Tool' software. The initial password is 1234. This

can be changed during installation. If you have lost the details of your password,

please contact the Customer Support Center.

Option via fire control panel

Standalone option

All parameters can be read with the

FXS2051

ASD Configuration Tool' software.

All parameters can be read with the

FXS2051

ASD Configuration Tool' software.

Certain parameters can be read from the fire

control panel.
Certain parameters can be configured from

the fire control panel.

All parameters can be configured with the

FXS2051

ASD Configuration Tool' software.

Only those parameters that cannot be

configured from the fire control panel can be

configured with the '

FXS2051

ASD

Configuration Tool' software.

You will find more information on configuring the aspirating smoke detector with the

FXS2051

ASD Configuration Tool' software in document A6V10332759. You will

find instructions for installing the driver in document A6V10348930.
You will find information about configuring with the software for the fire detection

system in document 009078 for fire control panels FC20xx and document

A6V10210424 for fire control panels FC72x.
See the chapter '

Applicable documents [➙

]

You will find information about the parameters in the chapter 'Operating modes

[➙

]

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands