manualshive.com logo in svg

Siemens EH675TK11E, Repair Instruction, Page: 98 / 113

Share
Download
Siemens EH675TK11E Repair Instruction Download Page 98

 
 

206_58300000141095_ara_en_k.doc – 04.10.a 

Seite 98 von 113 

 

5.19  Check polybox connections 

 

The procedure is as follows: 

1)  Check that the cable and connector that goes from the Polybox 

box to the oven is connected and in the correct position. 

2)  Check that the cable and connector that goes from the Polybox 

box to the hob is connected 

If all of this is good connected, open polybox box 

3) Check that both connectors (oven-polybox and hob-polybox) 

are good connected in the wake up module. 

5.19.1  Oven connector 

It should be verified that the connector that comes out of the box and 
goes in the oven is not polarized. 

 

 

The polarized connector is connected in the wake up module. 

 

 

 

 

5.19.2  Hob connector 

 

Check that the cable and connector that goes from the Polybox box to 
the hob is connected. See electrical diagram 
 

 

Summary of Contents for EH675TK11E


















































































































Reviews:

No comments