manualshive.com logo in svg

Siemens EH675TK11E, Repair Instruction, Page: 87 / 113

Share
Download
Siemens EH675TK11E Repair Instruction Download Page 87

 
 

206_58300000141095_ara_en_k.doc – 04.10.a 

Seite 87 von 113 

5.14  Checking the replacement part is correct 

5.14.1  Problem 

The replacement part does not coincide with the original 

5.14.2  Cause 

  The supplier has sent the wrong one. 

  The warehouse stock has got mixed up. 

  The module software is badly saved. 

5.14.3  Solution 

Inform central office for them to manage the incident. 

If the replacement part is an electronic item or module, the supplier 
code will be located on it. Check to see if this code corresponds to the 
code on the original part and if not, include this information in the 
report. 

  The label is located on the reverse side of TouchControl units. 

 

  The label is located on the front side of ELIN units. 

 

See table of supplier codes for replacement parts according to 
model. 

The left 1 ELIN is the one located on support ELIN-2. 

The left 2 ELIN is the one located on support ELIN-1. 

Summary of Contents for EH675TK11E


















































































































Reviews:

No comments