manualshive.com logo in svg

Siemens EH675TK11E, Repair Instruction, Page: 55 / 113

Share
Download
Siemens EH675TK11E Repair Instruction Download Page 55

 
 

206_58300000141095_ara_en_k.doc – 04.10.a 

Seite 55 von 113 

5.5 Radio 

interference 

5.5.1 

Problem 

The radio cannot be heard properly when operating the inductor. 

5.5.2 

Cause 

Inductor worktops and radios interfere with each other. 

Regulations establish certain emission and immunity levels for 
electronic devices in order to avoid such interference problems. If they 
occur, they may be caused by one of several reasons: 

  The worktop does not comply with the emission limits defined 

by the regulations governing the product. In our case, the 
worktops are certified according to European and international 
regulations EN55011 and CISPR 11. Therefore, they comply 
with the established emission limits. 

See the list of regulations and emission / immunity tests with 
which all our inductor equipment comply. 

  The radio does not comply with the immunity regulations for 

the product. 

  It is possible for interference to occur when the two devices 

comply with their respective regulations. These regulations are 
unable to cover the infinite possible number of individual cases 
(only general situations) and interference may occur. 

5.5.3 

Solution 

 

Check that the radio receiver complies with the 
corresponding immunity regulations for the product. 

In those cases where the two devices comply with their 
respective regulations and interference still occurs, it is 
recommended to separate them sufficiently. 

5.5.3.1 

List of regulations and emission / immunity tests 

 

EMC - Emission 

Code Title 

EN 55011 

Industrial, scientific and medical (ISM) radio-frequency 
Equipment. Electromagnetic disturbance characteristics. 
Limits and methods of measurement

 

 

EN 61000-3-2 

Electromagnetic compatibility (EMC) - Part 3-2: Limits – 
Section 2: Limits for harmonic current emissions 
(equipment input current greater than or equal to 16 A 
per phase) 

EN 61000-3-3 

Electromagnetic compatibility (EMC) – Part 3-3: Limits – 
Section 3: Limitation of voltage changes, voltage 
fluctuations and flicker in public low-voltage supply 
systems, for equipment with rated current =16 A per 
phase 

 

Summary of Contents for EH675TK11E


















































































































Reviews:

No comments