Siemens EH675TK11E Repair Instruction Download Page 5 | Manualshive

Page: 5 / 113

Siemens EH675TK11E Repair Instruction Download Page 5

206_58300000141095_ara_en_k.doc – 04.10.a

Seite 5 von 113

Special warnings for induction hobs!

Induction hobs comply with the safety and electromagnetic
compatibility regulations currently in force (EN50366). People with
fitted pacemakers should abstain from using or repairing such an
appliance. The operation of the appliance may interfere with the
operation of the pacemaker.

People with hearing aids may experience discomfort.

2.2

Repair warnings

Warning!

Never attempt to carry out repairs involving the indiscriminate
exchange of component parts.

Proceed in a systematic way, with reference to the technical
specifications supplied with the appliance.

The electronic plates should not be repaired, but replaced with original
spare parts. Exceptions are indicated in separate documents.

Components sensitive to electrostatic shock:

Respect EGB reference

Sharp edges:

Use protective gloves!

«
...
3
4
5
6
7
...
»

Summary of Contents for EH675TK11E


















































































































Reviews:

No comments