manualshive.com logo in svg

Siemens EH675TK11E, Repair Instruction, Page: 54 / 113

Share
Download
Siemens EH675TK11E Repair Instruction Download Page 54

 
 

206_58300000141095_ara_en_k.doc – 04.10.a 

Seite 54 von 113 

5.4 

Induction unit checks (ELIN) 

 

►

 

Checks must be performed with no voltage. 

►

 

Perform a visual inspection paying particular attention to any 
burnt components. 

►

 

IGBT checks. The resistance values between 

 

A 

B 

A 

B 

 

 

►

 

the feet of the IGBT’s must be: 

A >10 Kohm 

B > 5 Kohm 

 

►

 

Check that the thread on the inductor connection screw is not 
worn. If it is, replace the screw. If the thread problem is with 
the attachment piece, replace the entire unit.  

►

 

If the induction associated to this coil continues to fail when 
the above checks provided negative results, replace the coil. 

►

 

Check that the 2 fusible connections (for the power (B) and 
the mains supply (A)) are intact. If not, the entire coil should 
be replaced. 

 

 

 

A

 

B

Summary of Contents for EH675TK11E


















































































































Reviews:

No comments