manualshive.com logo in svg

Siemens EH675TK11E, Repair Instruction, Page: 105 / 113

Share
Download
Siemens EH675TK11E Repair Instruction Download Page 105

 
 

206_58300000141095_ara_en_k.doc – 04.10.a 

Seite 105 von 113 

5.23  Check supplied power for FlexInduction models 

 

 

 

Warning! 

: 

The flexInduction hobs don´t understand of pots number. When it is 
activated the flexi mode, the hob behaves like it had a unique pot on 
the zone. For this reason, we can only give the total power of the 
activated zones. We can not measure the power for each pot in the 
zone. 

In fact, for two kinds of pots, that is, with different material, placed in 
the combisurface, the power given to each pot can be different. 

 

5.23.1  Booster Function 

The booster function for combisurface only use the left ELIN to give 
the extra power. For this reason, there is only booster function, not 
superbooster function. And we have booster, though we had pots on 
the right zone. 

 

5.23.2  Check supplied power 

To be able to do the check, it is needed a pan of WMF brand and 
base diameter 21 cm, with spare part number 

570366

. 

 

 

 

We must place the pan in the quadrat inferior part and the supplied 
power measures must be the following. 

 

 

 

 

 

Summary of Contents for EH675TK11E


















































































































Reviews:

No comments